News:

Buy official forum merchandise here!

Main Menu

What did I do to my bike today

Started by Argh Oh, September 12, 2015, 12:04:33 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Mulley

Technically 2 days ago I installed fresh tires on my KTM 500.

Ready to go rip up the earth again.









2015 Versys 650 LT / 2016 Beta 300 RR / 2015 KTM 500 EXC

Nice Goat

Yesterday, I put 8 ounces of Slime in my rear tire, on the low pressure side of my Tubliss setup, and took the bike for a short ten mile ride.  This morning, my rear tire was still holding pressure.  Hallelujah!
IBA #63019 - 2022 Yamaha Tenere 700 - 2023 Yamaha XMAX 300
Deep thought: "Pie and coffee are as important as gasoline."

IceCold4x4

Quote from: Nice Goat on June 18, 2019, 05:24:06 PM
Yesterday, I put 8 ounces of Slime in my rear tire, on the low pressure side of my Tubliss setup, and took the bike for a short ten mile ride.  This morning, my rear tire was still holding pressure.  Hallelujah!
Weird mine held air with nothing added.

Sent from my SM-N950U using Tapatalk


Nice Goat

Quote from: IceCold4x4 on June 18, 2019, 05:51:39 PM
Weird mine held air with nothing added.

Apparently it is a common problem with the Motoz Arena Hybrid rear tire... don't know why.  I have a Pirelli on the front and it hasn't lost any pressure at all.
IBA #63019 - 2022 Yamaha Tenere 700 - 2023 Yamaha XMAX 300
Deep thought: "Pie and coffee are as important as gasoline."

IceCold4x4

Quote from: Nice Goat on June 18, 2019, 06:59:20 PM
Apparently it is a common problem with the Motoz Arena Hybrid rear tire... don't know why.  I have a Pirelli on the front and it hasn't lost any pressure at all.
I'm loving the Sedona mx907hp with the tubliss. Wears like iron and at 0 - 1 psi on the trails it grips like ape snot.

Sent from my SM-N950U using Tapatalk


Mulley

Quote from: Nice Goat on June 18, 2019, 06:59:20 PM
Apparently it is a common problem with the Motoz Arena Hybrid rear tire... don't know why.  I have a Pirelli on the front and it hasn't lost any pressure at all.
The inside lip has ridges so it's hard for the red liner to get a good seal against it.

It's part of my install process. I use No-Mar lube and Slime on every Tubliss tire. No leaks since I started doing this.
2015 Versys 650 LT / 2016 Beta 300 RR / 2015 KTM 500 EXC

KevinB

#456
I've been lucky (it's definitely not skill)...I use only soapy water for Tubliss install and the only one I've had leak was my very first one (not enough soapy water). I've installed three Arena Hybrids with no issues. After install, I usually inflate the low pressure side to @ 50 psi and let it sit overnight...dunno if it helps or is just a placebo.

Maybe I need to buy a lottery ticket while in TN this weekend...  :)

kylepeterson

splashed some gas in the tank and looked at the tires... mmmm think I'll just change the front end instead of doing seals today...  dirt devil here i come!
just give 'er the berries !

Fencejumper09

Finally received the clutch basket for the yz that I ordered on June 6!  Forgot to soak the clutch fibers over night so looks like I will try to button it up tomorrow.

First step was to remove the primary drive gear from the back of the oem basket by grinding off some rivets!



Then transfer the gear and rubber dampeners onto the new Barnett basket. this basket is slick with steel inserts along the wear edges. They will replace the steel inserts for $25 plus shipping both ways.  Not too bad!







The clutch fibers are soaking and hope to continue the install tonight.  The one hour between my daughter's bedtime and my bedtime does not allow for much time to wrench on the bikes!
2013 KTM 690 Enduro/Sumo
2013 KTM RC8R
2011 KTM 990 SMR (Oh Yeah)
2020 Beta 300 RR Race Edition
1985 Goldwing (ish)
2014 BMW 1200RT
Remember, a boss doesn't always do smart things, but he always does them like a boss. - Paebr332

2372ighost

Mounted a cup/cargo holder between my legs on the scooter.
2009 Vespa GTS250IE
2006 Ural Patrol
2011 Suzuki GSX1250 fa
2010 Husaberg FE390
1996 1400 Intruder

Fencejumper09

Slowly getting closer! Waiting on a couple seals and bearings that were bad in the replacement clutch cover and then I will be able to wrap this up!

Got a little distracted by the need for brakes and rotors on the truck!



2013 KTM 690 Enduro/Sumo
2013 KTM RC8R
2011 KTM 990 SMR (Oh Yeah)
2020 Beta 300 RR Race Edition
1985 Goldwing (ish)
2014 BMW 1200RT
Remember, a boss doesn't always do smart things, but he always does them like a boss. - Paebr332

KevinB

#461
Quote from: KevinB on June 18, 2019, 09:52:42 PM
I've been lucky (it's definitely not skill)...I use only soapy water for Tubliss install and the only one I've had leak was my very first one (not enough soapy water). I've installed three Arena Hybrids with no issues. After install, I usually inflate the low pressure side to @ 50 psi and let it sit overnight...dunno if it helps or is just a placebo.

Well, I jinxed myself...

Noticed my recently mounted Arena Hybrid was leaking down a little last weekend...went to load the bike this morning and it's totally flat.  >:(

Disregard my previous mention of luck or skill.

merc16

These billet eccentrics are almost too purty to install.

Sent from my SM-G975U using Tapatalk

Justin

KevinB

^^^ That is one bada$$ Zed.  :-\

merc16

#464
Thank$!

Sent from my SM-G975U using Tapatalk
Justin